How to Replace a Bathtub Yourself: Removing and also Replacing.
How to Replace a Bathtub Yourself: Removing and also Replacing.
Blog Article
This great article which follows about Tools You Need to Install a New Bathtub is indeed fascinating. Check it out for yourself and decide what you think about it.
Mounting a tub isn't exactly brain surgery, but it does need solid plumbing, woodworking, and sometimes, tiling skills. Changing an old bath tub with a brand-new one is likewise a reasonably tough job. If the old tub is readily accessible, the project can move speedily; if you need to open up a wall to eliminate the old tub and position the new bath tub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the task as well as are comfortable attempting it. Instead of employing a professional to take control of a halfway-completed task, it is much better to think about employing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new tub in your bathroom if you have currently acquired a brand-new tub and don't require to transform the plan of your previous water pipelines.
Your tools and also product list need to consist of the following:
Planning for the Setup
First of all, the sustaining framework provided with the bath needs to be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets device to avoid pressure on the tub.
Fit the flexible tap adapters to the bottom of both taps utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you use every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be fitted in its last position.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you ought to do is disconnect the water system. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. As soon as the supply pipelines have been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
Prior to moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bathtub in the required position. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four little points.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub until the spirit level reads degree.
To mount faucets, fit all-time low of the outermost adaptable tap adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the other faucet.
Turn on the water system as well as check all joints and also brand-new pipework for leakages and tighten them if necessary. Load the bath tub as well as also check the overflow electrical outlet as well as the typical outlet for leaks.
Ultimately, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the bathtub should wait till the tub has been used at least when as this will resolve it right into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines remain in place in between the tap and also the sink. Secure the tap in position with the producer given backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous type must be connected to the tap finishes first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to split an inflexible seal, creating the water to penetrate the wall between the bath as well as the tiling, resulting in issues with wetness as well as possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched paper or soft rope. Remember to always load the bath tub with water prior to securing, to allow for the activity experienced when the tub is in use. The sealer can fracture fairly very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is advisable to fit the tiles utilizing waterproof or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that write-up about How to Install a Bathtub through an acquaintance on a different web page. Enjoyed our article? Please share it. Help other people find it. We treasure reading our article about A Step-by-Step Guide to Installing a Bathtub.
Booking Page Report this page